Myq installation guide

Myq installation guide DEFAULT

1. Remove the pull tab from the new door sensor to

activate the battery.

2. Install the new door sensor with the included Fastening Strips or optional Screws

to a clean, dry area on top panel of garage door as shown below:

DOOR SENSOR COMPATIBILITY

Compatible with:

myQ

®

Smart Garage™ Hub models MYQ-G0301 and 821LMB.

Also compatible with MyQ Garage

TM

MYQ-G0201 and 821LM with use of

included Spacer.

Visit www.LiftMaster.com/door-sensor or

www.chamberlain.com/door-sensor for more information.

myQ SMART GARAGE DOOR SENSOR

MODELS MYQ-G0302, 821LMB-2SENSOR

To reduce the risk of SEVERE INJURY to persons:

• DO NOT enable the myQ Smart Garage Hub or the MyQ Garage if operating either

one-piece or swinging doors. To be enabled ONLY on a sectional door.

TEST DOOR SENSOR

WARNING: This product can expose you to chemicals including lead, which

are known to the State of California to cause cancer or birth defects or other

reproductive harm. For more information go to www.P65Warnings.ca.gov.

PROGRAM THE DOOR SENSOR

Test your door sensor every 6 months or if the myQ system is not working as expected.

Press and release the test button on the door sensor, the LED on the door sensor should blink and the

myQ Smart Garage Hub or MyQ Garage should beep. Wait 5-10 seconds, then repeat this test 5 more

times (wait 5-10 seconds between each test).

If the LED doesn’t blink or the myQ Smart Garage Hub or MyQ Garage doesn’t beep with each press,

replace the battery in the door sensor. Use a 3V Lithium battery size CR2450.

BUTTON

(Settings)

BUTTON 1

BUTTON 2

Wi-Fi Hub

LED

Test BUTTON

Door Sensor

CR2450 Battery

SENSOR

SENSOR

SENSOR

SENSOR

SENSOR

SENSOR

Fastening

Strips

Fastening

Strips

Door

Sensor

Front Cover

Screws

Screws

Top

Door

Sensor

Top

Top

Fastening Strips

Fastening Strips

Door

Sensor

Top

Spacer

Spacer

myQ Smart Garage HubMyQ Garage

Install using Fastening Strips

Optional: Install using Screws

NOTE: For solid wood or insulated garage doors ONLY.

Optional: Install using Screws

NOTE: For solid wood or insulated garage doors ONLY.

Install using Fastening Strips

NOTE: When installing this door sensor with a MyQ Garage, the included spacer MUST be installed

with the door sensor.

IMPORTANT: Press the door sensor and

spacer firmly to the garage door for 30

seconds to ensure a secure attachment.

Top Panel

of Garage

Door

Top Panel

of Garage

Door

Top Panel

of Garage

Door

Spacer

Top Panel

of Garage

Door

Top Panel

of Garage

Door

LED

Test

Button

Door Sensor

Pull Tab

MOUNT THE DOOR SENSOR

Use the myQ App to add a new door sensor to your second garage door (For details on the myQ app installation, please reference the

full manual at www.Chamberlain.com/myQsupport).

NOTE: If you are replacing an existing door sensor, please use the following steps to program your door sensor to both your Wi-Fi Hub

and your Garage Door Opener:

1. From your existing door sensor, recall if the Wi-Fi Hub beeped once or twice when the door sensor Test button was pressed.

2. On the Wi-Fi hub, press and release button 1 for 1 beep or button 2 for 2 beeps. The hub’s yellow LED will turn on.

3. On the new door sensor, press and release the Test button . The Wi-Fi hub will flash and beep indicating successful programming.

4. In the myQ app, check that you can open and close your garage door to confirm successful programming.

If you are replacing your door sensor, please follow these steps first:

1. Press and release the Test button on the existing door sensor until the Wi-Fi

Hub beeps. Note number of beeps (this indicates if original door sensor was

assigned to door 1 [1 beep] or door 2 [2 beeps] on the Wi-Fi Hub).

2. Remove existing door sensor from your garage door.

3. Remove the existing fastening strips from the garage door.

4. Open the existing door sensor and remove the battery.

5. Properly dispose of the door sensor and the battery.

Sours: https://www.manualshelf.com/manual/chamberlain/myq-g0302/installation-guide-french.html

MyQ Garage™

UNIVERSAL SMARTPHONE

GARAGE DOOR CONTROLLER

Model 821LM

INSTALLATION GUIDE

myLiftMaster.com

To reduce the risk of SEVERE INJURY to persons:

• DO NOT enable the MyQ Garage™ if operating either one-piece or swinging doors. To be enabled ONLY on a sectional door.

Read instructions thoroughly BEFORE beginning.

STOP

If using this product with residential door openers, this product must be used only with door openers manufactured after 1993 that utilize photoelectric

sensors. The photoelectric sensors are always located on or near the bottom of the door track.

INTRODUCTION

Thank you for your purchase of the 821LM MyQ Garage™. This product is designed to

connect to your current garage door opener through your existing Wi-Fi

allow you to remotely monitor and control the status of your door using a smartphone,

tablet or PC. In addition to remotely controlling your garage door, this product will also

allow you to control interior lighting when programmed to any MyQ

products as well. The following installation guide will walk you through the necessary

steps to quickly install the hardware and program to your garage door opener. Please

ensure that you have the serial number (located on the bottom of the Wi-Fi Hub or with

the Wi-Fi Setup card) prior to installing this product. For a full manual, please visit www.

liftmaster.com.

CARTON INVENTORY

NOT SHOWN: Installation Guide and Wi-Fi Setup Card for the customer

LEDs

LED

Test

Button

OVERVIEW

PRE-INSTALLATION REQUIREMENTS

• Compatible Garage Door Openers:

- LiftMaster

®

connection and

(310, 315, and 390 MHz) (Chamberlain, Do-It, Master Mechanic, Raynor,

True Value and Sears Craftsman are compatible with LiftMaster technology.)

- Genie

®

enabled Lighting

- Linear

- Stanley

- Wayne Dalton

• Verify there is a Wi-Fi router and broadband Internet connection at the site. Wi-Fi range

will vary depending on the thickness and number of walls, doors, or other barriers. The

average Wi-Fi range is about 300 feet.

• To test the strength of the Wi-Fi signal, take your device into the garage and turn on

its Wi-Fi. Connect your device to ensure you are receiving a good signal. If you don't

have a strong enough signal in the garage, a Wi-Fi range extender will be necessary

(available at most consumer electronics stores).

• Wi-Fi Hub Serial Number (located on the bottom of the Wi-Fi hub or with the Wi-Fi

Setup card)

For more information about compatible garage door openers, visit

myLiftMaster.com.

Wi-Fi Hub

Light

Bracket for Wi-Fi Hub

Door Sensor

Hardware for Door Sensor

(short screws)

Fastening Strips for

Door Sensor

®

with purple, yellow, green, or orange LEARN button

®

/Overhead Door

®

Intellicode I and II (315 and 390 MHz)

®

Mega Code (318 MHz)

®

Secure Code (310 MHz)

®

Keeloq (372.5 MHz)

Power Cord for W-Fi Hub

Hardware for Wi-Fi Hub

(long screws)

Warning Placard

Sours: https://www.manualslib.com/manual/976948/Chamberlain-Myq-Garage-821lm.html
  1. Chegg quiz answers
  2. Trail country exp
  3. Medibang textures

How to Connect a myQ Device to a Wi-Fi Network

Connecting a myQ Garage, myQ Smart Garage Hub, or Smart Garage Control to Your Home's Wi-Fi Network

myQ Garage

myQ Garage (MYQ-G0201 and 821LM)

myQ Smart Garage Hub

myQ Smart Garage Hub (MYQ-G0301 and 821LMB)

Smart Garage Control

Smart Garage Control

Before you can connect a myQ Hub to your home's Wi-Fi network, you will need the following:

Note: If at any point during the setup process you experience an error, follow the steps below to reset the myQ Garage, Smart Garage Hub, or Smart Garage Control and return the hub back to factory default .


How to Install and Set Up the Chamberlain Smart Garage Hub

How to Install the Chamberlain Smart Garage Control


Connect with Apple iOS Mobile Device

  1. Log into the myQ App.
  2. Check the image at the top of this FAQ to confirm your product
    • For myQ Garage and Smart Garage Hub tap Smart Garage Hub
    • For Smart Garage Control tap Smart Garage Control
  3. Review and tap Next on the What You Need screen.
  4. Plug in the Hub and tap Next.
    • Once it is plugged in, the LED on the Hub will blink blue. If the LED is not blinking blue, unplug the hub from the power supply and then plug it back in.
  5. Tap Yes if you have a blinking blue LED light. If you have a Smart Garage Control, go to step 8.
    • If you still don't have a blinking blue LED, press and hold the gear button until you see a flashing blue light, then release. Press and hold the gear button a second time, until the hub beeps. This will reset the hub. Unplug the hub from the power supply and then plug it back in.
  6. Scan the 10-digit serial number on the back of the hub.
    • If the serial number doesn't scan, tap Enter Serial Number Manually at the bottom of the screen. Type in the serial number and tap Done.
  7. Tap Join on the question, "Chamberlain" wants to join Wi-Fi Network "MyQ-NNN"?
  8. Select your home Wi-Fi network from the list.
  9. Enter your network password and tap Next.
  10. Tap Next on the Added to Wi-Fi screen.
  11. Remove the tab in your door sensor and tap Next.
  12. Test your door sensor by pressing the button as indicated in the app, tap Next.
  13. Go through the steps to pair your door sensor to your hub then tap Next.
  14. Press and release the button on the door sensor. The Hub will beep and flash. If it doesn't, test the door sensor using this guide: How to Test the Door Sensor
  15. Tap Next on the Door Sensor is Paired screen.
  16. Follow the in-app steps or watch the video to install the door sensor.
    • You can skip these steps in the app by pressing Skip Install Help at the bottom of the screen
  17. Tap Next on the Pair to Motor screen.
  18. Read the warning and click Next.
  19. Use a ladder to access your garage door motor and tap Next.
  20. Select the brand of your garage door opener.
  21. Locate your learn/program button and tap Found It.
    • If prompted, select the color of your learn/program button.
    • This will be the same button you use to program remotes and keypads
  22. Press and quickly release the learn/program button on your garage door opener motor head and tap Next.
    • This will cause your garage door opener to move.
  23. When the garage door opener is paired, tap Next.
  24. Name your garage door and tap Next.
  25. Mount the hub per the app instructions.
    • You can watch the video or follow the in-app steps provided.
  26. Tap Finish when you have successfully installed the hub.
  27. Tap the garage door in the app to activate the door.

Note: Do not operate the garage door opener until installation has been completed.


Connect with Android Mobile Device

  1. Log into the myQ App.
  2. Check the image at the top of this FAQ to confirm your product
    • For myQ Garage and Smart Garage Hub tap Smart Garage Hub
    • For Smart Garage Control tap Smart Garage Control
  3. If prompted, enable your location services.
  4. Review and tap Next on the What You Need screen.
  5. Plug in the hub and tap Next.
    • Once it is plugged in, the LED on the hub will blink blue. If the LED is not blinking blue, unplug the hub from the power supply and then plug it back in.
  6. Tap Yes if you have a blinking blue LED light.
    • If you still don't have a blinking blue LED, press and hold the gear button until you see a flashing blue light, then release. Press and hold the gear button a second time, until the hub beeps. This will reset the hub. Unplug the hub from the power source and then plug it back in.
  7. Tap MyQ-NNN showing in the Discovered screen.
  8. Select your home Wi-Fi network from the list.
  9. Enter your network password and tap Next.
  10. Tap Next on the Added to Wi-Fi screen.
  11. Remove the tab in your door sensor and tap Next.
  12. Test your door sensor by pressing the button as indicated in the app, tap Next.
  13. Go through the steps to pair your door sensor to your hub, tap Next.
  14. Press and release the button on the door sensor. The hub will beep and flash. If it doesn't, test the door sensor using this guide: How to Test the Door Sensor
  15. Tap Next on the door sensor is paired screen.
  16. Follow the in-app steps or watch the video to install the door sensor.
    • You can skip these steps in the app by pressing Skip Install Help at the bottom of the screen
  17. Tap Next on the Pair to Motor screen.
  18. Read the warning and click Next.
  19. Use a ladder to access your garage door motor and tap Next.
  20. Select the brand of your garage door opener.
  21. Locate your learn/program button and tap Found It.
    • If prompted, select the color of your learn/program button.
    • This will be the same button you use to program remotes and keypads
  22. Press and quickly release the learn/program button on your garage door opener motor head and tap Next.
    • This will cause your garage door opener to move.
  23. When the opener is paired, tap Next.
  24. Name your garage door and tap Next.
  25. Mount the hub per the in-app instructions.
    • You can watch the video or follow the in-app steps provided.
  26. Tap Finish when you have successfully installed the hub.
  27. Tap the garage door in the app to activate the door.

NOTE: Do not operate the garage door opener until installation has been completed.


The below steps are only needed if you encounter an error when setting up your myQ Smart Garage Hub or Smart Garage Control.

Smart Garage Hub

Smart Garage Hub Settings Button

Smart Garage Control

Smart Garage Control Settings Button

Erase Wi-Fi settings

Erasing the Wi-Fi settings allows you to reset the Wi-Fi settings on the hub.

  1. The Green LED MUST be on or blinking to erase Wi-Fi settings.
  2. Press and hold the Settings button on the hub until the blue LED blinks, indicating Wi-Fi is ready to be set up.

Factory Default

Setting the hub back to factory default erases the Wi-Fi settings, door sensors and removes the garage door opener from the myQ account.

  1. Press and hold the Settings button on the Wi-Fi hub until the blue LED blinks then release.
  2. While the blue LED is blinking, press and hold the Settings button again until the hub beeps. The Wi-Fi hub is set to factory default.

If you are having trouble connecting to your home Wi-Fi network, see Unable to Connect a myQ Garage, myQ Smart Garage Hub, or Smart Garage Control to Home Wi-Fi Network Overview.

Sours: https://support.chamberlaingroup.com/s/article/How-to-Connect-the-Smart-Garage-Hub-to-a-Network
MyQ X - Installation Process

How to Install myQ Smart Garage Door Opener

If you install a smart garage door opener, you’ll never forget to close the garage again. Plus, you can have your Amazon deliveries dropped off in your garage, so you don’t have to worry about them being stolen. Here’s how to install the Chamberlain myQ smart garage door opener.

Note: Before you begin, it is important to check the WiFi signal strength in your garage. Stand near the garage door opener and look at the WiFi signal bar along the top of your phone’s screen. If your WiFi signal is less than 1 bar, your garage door opener won’t work. You will either need to move your WiFi router closer to the garage or buy a WiFi extender.

how to install myq garage door opener

Note: Also, make sure that your garage door opener is compatible with myQ. Otherwise, you will have to purchase additional accessories to make them work together. If you want to see if your garage door opener is compatible, check out this list.

HT blog ad myIQ

How to Install the myQ Garage Door Opener App

  1. Download the myQ Garage and Access Control App. You can find the app on the Apple App Store (for iPhone) or Google Play Store (for Android).
  2. Open the myQ app and sign-up for an account. You need to enter a username, password, email address., country, and zip code.
  3. When you’re done, click “submit.”
    how to sign up with myq app
  4. Use your smartphone to check your email for a message from myQ.
  5. Then click the link in the email that says Click here to complete registration. A link in the email should take you back to the myQ app. If you don’t see the email, be sure to check your spam folder.
    myq click here to complete registartion
  6. Log into the myQ app with your new username and password.
  7. Then tap Add Device.
  8. Finally, select MyQ Smart Garage Hub from the list of devices.
how to install myq garage door opener

How to Connect the myQ Hub to Your Phone

  1. Plug the hub into a temporary outlet. A blinking blue light will appear on the front of the hub.
    myq hub blinking blue light
  2. Use the app to pair your phone with the hub. If you’re an iPhone user, you can scan the hub’s serial number, located at the back of the hub. Or you can enter it manually by tapping the Enter Serial Number Manually button at the bottom of your screen.
    myq scan bar code iphone

    If you’re an Android user, all you have to do is tap the hub’s name when it shows up as a discovered device. This will be something like MyQ-123.

    myq android connect app
  3. Choose your WiFi network and type in its password. The app might show several WiFi networks within its range. Make sure you choose the right one.
    choose a wifi netwrok and enter password
  4. Wait for the app to connect to your WiFi network. The LED on the hub will flash to show it is connecting to the network. It will show a steady green light when it is connected.
how to install myq garage door opener

How to Pair the Hub and the Garage Door Sensor  

  1. Pull out the protective tab from the garage door sensor. This will activate the batteries.
    myq protective tab
  2. Test the door sensor. You can do this by pressing the button on the lower half of the circle. You should then see a red light at the top of the device.
    Test the door sensor app
  3. Wait for a bright light to flash in the middle of the hub. This means the hub has found the sensor.
    for a bright light to flash in the middle of the hub
  4. Press the sensor’s button on the lower half of the circle again. A beep will confirm that the hub and sensor are now paired or connected. You can now install the sensor to your garage door.
how to install myq garage door opener
smart home

How to Install the myQ Garage Door Sensor

  1. Choose the garage door’s top panel where you want to mount the sensor. Wipe off any dust with a clean, dry cloth.
    Choose the garage door’s top panel where you want to mount the sensor
  2. Attach the supplied adhesive strips to the back of the sensor. To do this, peel off the adhesive cover and attach the strip to the back of the sensor one at a time. Remove the two remaining adhesive covers from the strips. Warning: do not split the strips apart.
    Attach the supplied adhesive strips to the back of the sensor
  3. Firmly position the sensor on the garage door panel. Make sure the sensor is upright: the word “top” on the sensor should face upwards, and you can read the myQ logo correctly. 
Firmly-position-the-sensor-on-the-garage-door-panel

How to Pair the Garage Door Opener With the myQ Smart Garage Hub

  1. Close your garage doors and clear the entrance of obstructions. Your garage door might open and close during the final pairing. Also, ensure that the garage door opener is plugged in.
  2. Select the brand of your garage door opener in the myQ app. This tells the hub to start looking for your door opener. Meanwhile, you should get on your ladder to access the garage door opener on the ceiling of your garage.
    choose brand
  3. Find the learn/program button on your garage door opener. This button could be on the back, side, or bottom of the unit. When you find it, click “found it” on the app. The app might also prompt you to select the color of your learn button, which could be yellow, purple, orange, green, or red.
    Find the program button on your garage door opener
  4. Press the learn button on the door opener until you see the LED next to the button light up. Don’t press the learn button too long. Otherwise, you might un-pair your current garage door remote controls.
  5. Wait for the hub to find the garage door opener. The app might need several attempts to do this. When successful, a checkmark will appear in the app, and you’ll be prompted to click “next.”
  6. Finally, type in a name for your garage door opener. This can be any name you want.  
how to install myq garage door opener

How to Mount the myQ Hub Near the Garage Door Opener

  1. Get your tools ready. You will need a pencil/marker, a Philips screwdriver, a 5/32 drill bit and drill, a stepladder, and safety goggles. The bracket, screws, and wall anchors are provided with the hub.
    Tools
  2. Choose a spot on the ceiling 5 to 6 feet from the garage door opener. You should choose a spot where you can see the flashing light of the hub from the entrance of your garage. It should also be near a power outlet.
    choose a place
  3. Mark the ceiling using the holes in the mounting bracket as a guide. The bracket’s open ends should face the ceiling.
    Mark the spot on the ceiling using the holes in the mounting bracket as a guide
  4. Drill holes into the marked spots. 
  5. Then push in the anchors, making sure they are flush against the ceiling.
  6. Screw the mounting bracket into place. 
    Screw the mounting bracket into place
  7. Slide the garage hub onto the bracket until it clicks into place.
  8. Plug the power cord into the hub. If your cord is too long, you can wrap the excess around the hub.
  9. Plug the power cord into the power outlet. Make sure the hub’s green LED light turns on.
    green light myq
  10. Finally, tap the garage icon on the app to open and close the garage door.
how to install myq garage door opener

Congratulations! That is all you need to install the myQ smart garage door opener. Bitten by the smart home bug? See how you can make your home even smarter by learning about the best smart home devices for beginners.  

HelloTech editors choose the products and services we write about. When you buy through our links, we may earn a commission.

Updated on August 31, 2021

Was this article helpful?

Related Articles

Sours: https://www.hellotech.com/guide/for/how-to-install-myq-garage-door-opener-hub

Installation guide myq

IMPORTANT!

READ ME

PLEASE KEEP THIS CARD TO COMPLETE THE WI-FI

SETUP FOR THE UNIVERSAL GARAGE DOOR

SMARTPHONE CONTROLLER.

MyQ Garage

Universal Garage Door Smartphone Controller

MODEL 821LM

WI-FI SETUP CARD

TO SETUP THE WI-FI YOU MUST HAVE THE FOLLOWING:

• Router with Wi-Fi

• Broadband Internet Connection

• Wi-Fi Hub Serial Number listed below (also located

on the bottom of the Wi-Fi hub):

TM

Setup the Wi-Fi

The blue LED on the Wi-Fi hub must be blinking.

If the blue LED is not blinking, press the test

button on the door sensor or unplug the power

supply for the Wi-Fi hub and reconnect the

power supply (the blue LED will blink).

iPhone

®

and iPod touch

®

*:

1. Ensure your iPhone or iPod touch is connected to your home Wi-Fi network, if not

connect to network.

2. On your iPhone or iPod touch, go to Settings > Bluetooth

3. Find the Bluetooth device with the "MyQ" prefi x and select it to pair.

4. Follow the iPhone or iPod touch prompts to add the Wi-Fi hub to your Wi-Fi network

and download the LiftMaster MyQ

®

Home Control app.

NOTE: It may take a few minutes for the Wi-Fi hub to connect to the Internet. When fully

connected to the Internet, the green LED on the Wi-Fi hub will be on solid.

5. If unsuccessful, follow "All Other Devices". Launch the app, follow the onscreen

instructions to sign up and complete the setup.

"Made for iPod" and "Made for iPhone" mean that an electronic accessory has been designed to connect specifi cally

to iPod or iPhone respectively, and has been certifi ed by the developer to meet Apple performance standards. Apple

is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note

that the use of this accessory with iPod or iPhone may affect wireless performance.

All Other Devices:

1. Go to the mobile device's Wi-Fi Settings and turn on Wi-Fi.

2. Locate the list of available Wi-Fi networks and select the network with the "MyQ" prefi x.

3. Launch the mobile device's web browser and go to http://setup.myqdevice.com".

4. The MyQ Wi-Fi Setup page will open.

5. Follow the onscreen instructions to sign up and complete the setup.

NOTE: The network's name and its associated security key/password (if applicable) will be

required.

*Made for: iPhone

®

5, iPhone 4S, iPhone 4, and iPhone 3GS, iPod touch

generation)

www.myliftmaster.com

Apple, iPhone, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.

The Bluetooth

®

word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such

marks by The Chamberlain Group, Inc. is under license. Other trademarks and trade names are those of their

respective owners. Wi-Fi

®

is a registered trademark of Wi-Fi Alliance.

Wi-Fi Hub

Light

The LEDs are visible

when directly facing

the Wi-Fi Hub.

Blue LED

Green LED

Yellow LED

®

, and turn on Bluetooth.

OR

®

(3rd, 4th and 5th

Sours: https://www.manualslib.com/manual/821937/Chamberlain-Myq-Garage.html
How to Install and Set Up the LiftMaster Smart Garage Camera Using the myQ App

.

You will also be interested:

.



276 277 278 279 280